Final Prototype Helmet Recycled
four-dimensional in the Fourth Dimension by Marcelo Ambrogi - Taubaté - SP -
Brazil
The Benefits of Using Recycled the unprecedented four-dimensional helmet on Fourth Dimension in filming and photography:
1 - Let you enjoy filming in 4D, 720 degree and wide angle of 360 degrees in an intelligent and cost, even recycling materials that could possibly pollute rivers, seas and native forests;
2 - Make professional and amateur footage of privileged angles, never before experienced, using the imagination with recycled materials is pretty cool, interesting and fun.
3 - Get unique and personal footage without the help of a tripod or second person, facilitating and giving mobility to the angles and filming.
4 - Allows you to have the angles at times and turns anti-clockwise from filming inside or outside the angle of the helmet over his person, a condition that promotes film sensitizes very unique and its peripheral movement resulting from your walk, walk, or cycling.
>> How to build a helmet recycled:
1 - Bicycle helmet that fits right in your head and get fixing buckles;
2 - Base square wooden 150 x 150 mm with a soapbox car 25 mm in diameter placed in the center.
3 - Rebar construction used of 4000 mm length and 4 mm in diameter;
4-1 nut 10 mm diameter screw with a 10 x 60 mm. We use to solder and attach the camera;
5 - Four screws camera 4 x 30 mm in length. We use to lock and unlock the camera.
Anyway before building the equipment make sure everything is firm and well reinforced. Do not risk it and if you do not have constructive skills and locksmiths do not, ask a qualified professional.
Tools:
1 - Serra arc;
2 - drill bit and a 4 mm;
3 - Hammer;
4 - Tape;
6 - Goggles;
7 - Mascara electric welding, if you choose to weld.
Note: If you do not want to solder the four mounting nuts you can bend the rebar itself in small circles and do not use nuts, also gives some more support is more rustic.
How-to:
With the helmet in hand, make three holes for supporting the base of the shaft on the slope you see fit, check the minimum distance of 500 mm and the angle of view of the camera you will use, bend the rebar in the middle and lock the first nut after each 40 mm bend makes an angle of 90 degrees, distance 90 mm and bend over again. Write back to the other rods.
Place remaining nuts on the ends of the rod where it will set the helmet. Adjust the inner moorings and guide the rod to the desired angle 90 degrees when I used my right side.
Get Tested for photography and filming and fasten.
Check the camera installation and repair if necessary, and perform paint and base of the stems.
Use:
With everything assembled, shooting to the orienting field of view or side adjust the screw, turn the camera and start filming.
I make adjustments 4D and 720 degrees of the four equipment (machines installed).
Before you start filming I test the quality and balance of films produced and relate my contribution walk my footage.
Conclusion:
The proposal is to make a rod shot, simple and mostly free of charge collapsible and easy to maintain if necessary and even total disassemble for transport.
The environmental benefits of using recycled helmet fixed arm:
1 - Awake awareness of recycling for educational and scientific purposes;
2 - Speed of development and construction of photographic rods;
3 - Re-use of discarded materials that could pollute the environment, and now will produce film and photography into our home, so intelligent, creative and spontaneous.
Thus able to successfully photograph our journey on foot or by bike, it's pretty cool and fun. But always be careful and not expose yourself to unnecessary risks.
Precautions and Tips:
Whenever sawing and drilling you should wear eye protection and never be flustered when welding and cutting materials, making sure you are well posted and do not be swinging, any change must be considered before building or modifying the helmet, remember that is recycled only and has no cost.
You will spend two hours of service labor.
E-mail: arteverdadeira@gmail.com
The Benefits of Using Recycled the unprecedented four-dimensional helmet on Fourth Dimension in filming and photography:
1 - Let you enjoy filming in 4D, 720 degree and wide angle of 360 degrees in an intelligent and cost, even recycling materials that could possibly pollute rivers, seas and native forests;
2 - Make professional and amateur footage of privileged angles, never before experienced, using the imagination with recycled materials is pretty cool, interesting and fun.
3 - Get unique and personal footage without the help of a tripod or second person, facilitating and giving mobility to the angles and filming.
4 - Allows you to have the angles at times and turns anti-clockwise from filming inside or outside the angle of the helmet over his person, a condition that promotes film sensitizes very unique and its peripheral movement resulting from your walk, walk, or cycling.
>> How to build a helmet recycled:
1 - Bicycle helmet that fits right in your head and get fixing buckles;
2 - Base square wooden 150 x 150 mm with a soapbox car 25 mm in diameter placed in the center.
3 - Rebar construction used of 4000 mm length and 4 mm in diameter;
4-1 nut 10 mm diameter screw with a 10 x 60 mm. We use to solder and attach the camera;
5 - Four screws camera 4 x 30 mm in length. We use to lock and unlock the camera.
Anyway before building the equipment make sure everything is firm and well reinforced. Do not risk it and if you do not have constructive skills and locksmiths do not, ask a qualified professional.
Tools:
1 - Serra arc;
2 - drill bit and a 4 mm;
3 - Hammer;
4 - Tape;
6 - Goggles;
7 - Mascara electric welding, if you choose to weld.
Note: If you do not want to solder the four mounting nuts you can bend the rebar itself in small circles and do not use nuts, also gives some more support is more rustic.
How-to:
With the helmet in hand, make three holes for supporting the base of the shaft on the slope you see fit, check the minimum distance of 500 mm and the angle of view of the camera you will use, bend the rebar in the middle and lock the first nut after each 40 mm bend makes an angle of 90 degrees, distance 90 mm and bend over again. Write back to the other rods.
Place remaining nuts on the ends of the rod where it will set the helmet. Adjust the inner moorings and guide the rod to the desired angle 90 degrees when I used my right side.
Get Tested for photography and filming and fasten.
Check the camera installation and repair if necessary, and perform paint and base of the stems.
Use:
With everything assembled, shooting to the orienting field of view or side adjust the screw, turn the camera and start filming.
I make adjustments 4D and 720 degrees of the four equipment (machines installed).
Before you start filming I test the quality and balance of films produced and relate my contribution walk my footage.
Conclusion:
The proposal is to make a rod shot, simple and mostly free of charge collapsible and easy to maintain if necessary and even total disassemble for transport.
The environmental benefits of using recycled helmet fixed arm:
1 - Awake awareness of recycling for educational and scientific purposes;
2 - Speed of development and construction of photographic rods;
3 - Re-use of discarded materials that could pollute the environment, and now will produce film and photography into our home, so intelligent, creative and spontaneous.
Thus able to successfully photograph our journey on foot or by bike, it's pretty cool and fun. But always be careful and not expose yourself to unnecessary risks.
Precautions and Tips:
Whenever sawing and drilling you should wear eye protection and never be flustered when welding and cutting materials, making sure you are well posted and do not be swinging, any change must be considered before building or modifying the helmet, remember that is recycled only and has no cost.
You will spend two hours of service labor.
E-mail: arteverdadeira@gmail.com
Final Prototype Helmet Recycled four-dimensional in the Fourth Dimension by Marcelo Ambrogi - Taubaté - SP - Brazil
http://youtu.be/KSMbnAQ-NDc
